1. Manual Secadora Electrica General Electric Motors
2. Manual Secadora Electrica General Electric Smoker
3. Partes Para Secadoras General Electric

Clothes Dryer Repair

Secadora A Gas General Electric - MercadoLibre Peru. General Electric Gfdn110elww Use And Care Manual. Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon Secadoras 364B7130P03-2 03/11/10 GE. Img395.jpg general electric lvge 011. Jc manual.pdf wbvh6240. Lav 2090 electromecanico 1.pdf EWA4600G0 GJRR4170H0 GJSR4160H0 WCSR4170G0 WHDRR41.

GENERAL ELECTRIC

4-1 MACHINE LAYOUT

Figure GE-1 shows the general layout of these machines.
The rear of the drum is supported by a small shaft and bearing. The front of the drum is supported by glide pads. Older machines used two small glide pads underneath the drum for support (See figure GE-4) Newer machines have a 3-glide assembly attached to the inside front of the cabinet.
The blower fan is attached directly to the front of the drive motor. The drive belt comes directly off the rear of the motor and goes completely around the drum.

Electrical model GE dryers use a double heater element. One of the two elements is energized for the low heat cycle; both heaters are energized for high heat. Late models have the heater elements contained in a cylindrical heater chamber fastened to the right front baseplate of the machine. In earlier models, the heaters are in a circular chamber directly behind the drum.

Figure GE-1: General Layout

GE went kind of crazy with thermostats for a while. I'm sure their design engineers know what they're doing, but..well, let's just say that to my experience, GE machines tend to have more thermostats than other brands. Moreover, they tend to migrate from model to model. Your model may have thermostats in just about any of the places shown in figure GE-2.

4-2 COMMON PROBLEMS

The most common problems with these machines are:
1) Noisy operation. If you hear a very loud clattering sound, the belt could be broken. When the belt breaks in these machines, the tensioner touches the motor pulley and causes one heckuva loud racket. To confirm this diagnosis, check to see if the drum is turning. Replace the belt as described in section 4-3.
Another common cause of noise happens when the drum front support glides wear out. This causes a pronounced scrubbing sound (metal-to-metal.)

Figure GE-2: Possible Thermostat Locations

Manual Secadora Electrica General Electric Motors

Also, if they are worn badly, you will see the top inner lip of the drum wearing the inside top of the clothes port. The solution is to remove the front of the cabinet as described in section 4-3 and replace the drum front support glides .
A squeaking or squealing noise can be caused by the rear drum bearing wearing out. Remove the drum and replace the bearing as described in section 4-4.
2) Heating problems. Download video upin ipin free mp4. Diagnose and repair as described in Chapter 2.

4-3 CABINET ACCESS PANELS (Fig. GE-3)

ACCESS TO BELT TENSIONER, REAR BEARING OR GAS BURNER
Each of these components has its own access panel:
The gas burner access panel is located in the lower right front of the cabinet. To open, push in on the top of the panel. The bottom is on nylon snaps and will pop off. Then just lift the panel out.
The belt tensioner is accessed through the bottom panel of the back of the dryer.
The rear drum support bearing is accessed through the small panel in the center of the back of the dryer. In newer style machines, there is no access panel; you simply remove the cabinet top and front and slide the drum out.

Figure GE-3: Opening the Cabinet

CABINET FRONT PANEL AND DRUM GLIDES
Several different methods have been used to fasten the front panel to the cabinet top (figure GE-3). Unscrew the screws or pop the catches and lift the lid of the dryer.
NOTE: If you are testing the heaters of rear-heater models, the terminals are accessible at this point. Look to the rear of the drum on the right side. You can test them as described in section 4-6. In bottom-heater models, you must remove the front panel as described below to test the heater element.

Loosen, but do not remove, the two screws at the bottom front corners of the front panel of the cabinet.
Unscrew the two screws at the top front corners inside the cabinet. Disconnect any door switch wires and lift off the front panel of the dryer.
You can replace the belt at this point, without removing the drum. Release the belt tension as described in section 4-4. You can slip the belt between the drum and the glides.
Once the cabinet front panel is off, inspect the blower wheel at the lower left corner of the dryer for foreign debris, excessive lint or broken blades.

The blower hub has a two-piece clamp which will fall apart if you remove it, so do not remove the hub clamp unless you plan to remove the whole motor and blower housing assembly as described in section 4-4.
Also while the cabinet front panel is off, inspect the felt seal inside the front panel for wear, excessive lint, or any debris that might be stuck to it.
Remove and inspect the front drum support glides as shown in figure GE-4. Newer models have three glides attached to the inside of the front panel. Whether they're badly worn or not, it's a good idea to replace them as cheap insurance against future problems.

4-4 DRUM REMOVAL

In old-style machines, the drum must be removed to service the electric heaters, or to remove the blower or motor, to replace the rear drum bearing.
Open the rear cabinet bottom panel. Reach inside and remove the belt tension as shown in figure GE-5.

Figure GE-5: Belt Tensioner

Older models have a circlip ('E'- ring) holding the rear drum shaft in place and a small drum bearing inspection plate in the center of the rear of the dryer to access this circlip. (See Figure GE-3) Later models do not have this inspection plate nor the circlip. If you have an inspection plate, remove it now.

Figure GE-4: Drum Glides

Manual Secadora Electrica General Electric Smoker

Inside, you will see the drum support shaft and an 'E-'ring holding it in place. Remove the 'E-'ring with a small screwdriver. If you have a magnet, you may also be able to use it to avoid dropping the ring inside the dryer.
There are spacer shims between the bearing and the 'E-'ring. There are more shims inside the bearing, between the bearing and the drum. Some are nylon and some are metal. Note how they come off, and make sure you put the shims back on the same way they come off.
Remove the cabinet front panel as described in section 4-3. In certain models, you will also need to remove the front drum support glides to get the drum out.
Once the cabinet front panel is off, you should be able to lift and slide the dryer drum straight outward.
While the machine is open, vacuum out all accumulated lint. Be careful not to knock any wires loose.

4-5 BLOWER SERVICE

If you need to replace the blower wheel on an old style machine, you must remove the dryer drum as described in section 4-4. Pull the six screws holding the blower housing to the baseplate, remove the motor mounting nuts and pull out the motor and blower housing as an assembly. In some models, you must remove the tensioner arm to get the motor assembly out.
When re-installing the blower, you must align the blower wheel so it does not touch the blower housing. To do this, loosen (but do not remove!) the clamp that holds the wheel to the motor shaft.

4-6 ELECTRIC HEATERS

The heater elements can be tested without removing them. Note which lead goes on which terminal and remove the leads from the terminals. The two heater elements are tested separately, if one is bad, BOTH must be replaced. Test them as described in Chapter 2. The elements are wired as shown in figure GE-6.

Figure GE-6: GE Clothes Dryer Heater Elements

Partes Para Secadoras General Electric

In rear-heater (circular) models, the elements must be pre-stretched to the correct length before installing. Follow the instructions that come with the new heaters. DO NOT OVERSTRETCH THEM! It's better to leave them an inch or so short, and work them to the proper length when the heater element is in place in the dryer. Also, make sure you inspect the porcelain insulators and replace any that are cracked or broken.

In bottom heater GE clothes dryer models, the whole heater chamber is replaced. Remove the two screws holding down the front end of the chamber and the back end just slips out of the heat riser.

• • 1

    Consumer Support
  • 1

    Installation Instructions
  • 1

    Table of Contents
  • 2

    Important Safety Instructions
  • 2

    What to Do if You Smell Gas
  • 3

    Proper Installation
  • 5

    Save These Instructions
  • 6

    Dryer Control Panel
  • 7

    Cycle Options
    • 8

      Dryer Cycles
    • 8

      Fabric Type
    • 8

      Timed Dry
    • 15

      Drum Lamp
  • 15

    Dryer Features
  • 15

    Drying Rack
  • 16

    Loading and Using the Dryer
  • 17

    The Dryer

• 18

  Installation Instructions

  • 18

    Before You Begin
    • 18

      For Your Safety
    • 18

      California Safe Drinking Water and Toxic Enforcement Act
    • 19

      Location of Your Dryer
  • 21

    Connecting a Gas Dryer
  • 22

    Gas Requirements
  • 25

    Connecting an Electric Dryer
  • 28

    Exhausting the Dryer
  • 33

    Final Setup
  • 35

    Reversing the Door Swing
  • 37

    Switching the Washer and Dryer Backsplashes

• 41

  Troubleshooting Tips

  • 41

    Problem Solver
  • 43

    Dryer Warranty
  • 44

    Consumer Support
  • 44

    Warranty